KT200 Review
Here is a customer’s review about KT200 ECU programmer. I have KT200 ecu programmer. It’s a very good tool, no need to open ecu. EDC16 full in bench, EDC17 too. It can make BDM, JTAG, VR read offline dongle in… Continue Reading
ECUHELP kt200 ECU Programmer
How to Read and Write VW EDC 16U1 EEPROM with KT200?
Master the skill of using KT200 ECU programmer to read and write VW EDC 16U1 EEPROM efficiently. This comprehensive guide offers easy-to-follow steps to ensure a successful ECU programming procedure. Step 1: Connect KT200 ECU Programmer and Prepare ECU Begin by connecting… Continue Reading
How to Solve KT200 “Open Device Error”?
Customers inquired, “What steps should be taken to resolve the ‘Open Device Error’ prompt on my KT200 ECU programmer?” Solutions from OBD2GATE.com: Case one: The device is KT200 ecu programmer full version with offline workstation Problem is shown in the… Continue Reading
How to Choose Between KT200 and PCMTuner?
Many customers don’t know the differences between KT200 ECU Programmer and PCMTuner. OBD2GATE has compared these two to help you choose. We hope our comparison makes your decision easier. Both KT200 ECU Programmer and PCMTuner are good tools, but they… Continue Reading
How to Read and Write Fiat IAW 59F with KT200?
KT200 ECU programmer has successfully read and written Fiat Marelli 59F ECU many times without problem. Here is the procedure: Determining Your Hardware Version: Verify whether your hardware version is above or below 100. For Marelli 59F HW <100: KT200 read and… Continue Reading
How to fix ECUHELP KT200 “Turn the dashboard off and back on…”?
KT200 error “Turn the dashboard off and back on, then wait for 10 sec before continue”. Look at the images below. Solution: Starting from where I started the GREEN ARROW. it’s the 12th pin and not the 11th where you… Continue Reading
ECUHELP KT200 Siemens SIM2K-140 141 341 D160 Boot Pinout
KT200 ECU Programmer Siemens SIM2K-140/141/341/D160 on the desktop (large connector) : 1,3,5 – ECU Ground (just connect one of the contacts) 77 – CAN-High 78 – CAN-Low 76 – K-Line 2 – + 12V (ignition on) 4 – + 12V (main… Continue Reading
ECUHELP KT200 ECU Programmer Feedback
ECUHELP KT200 ECU programmer can perform ECU maintenance chip tuning, DTC code removal, OBD/BOOT/BDM/JTAG, and multiple protocols. And it is the Master version, means it can read and write ECU data, read it in BIN unencrypted format, allows you to modify… Continue Reading
Way of ECUHELP KT200 clone DCM6.2C PSA in boot & JTAG mode
ECUHELP KT200 ECU Programmer can clone DCM6.2C PSA, it reads and writes Flash+EEprom in BOOT mode and JTAG , if you have org AUTOTUNER you will find it reads FLASH+EEprom but writes only FLASH. How to use KT200 clone DCM6.2C PSA in boot & JTAG mode?… Continue Reading
ECUHELP KT200 BOSCH MD1CS018 pinout and video
ECUHELP KT200 ecu programmer can read and write BOSCH MD1CS018 ECM without any errors, the operation way is as the same as mg1cs026. MD1CS018 pinout Read the follow youtube video for operation steps: https://www.youtube.com/watch?v=8p-L_yjOQ6I www.obd2gate.com
